|
|
|
|
|
Author |
Message |
mspaw Community Member
Joined: 18 Mar 2007 Posts: 234 Location: Sacramento CA
|
Posted: Fri May 06, 2011 9:08 pm Post subject: Machined Replacement Barrel |
|
|
After a long departure here they are. The specs are the same as last time with the correction that the taper on the front matched the worldcon one.
For those of you that missed out on the last run but had signed up ill try to contact you personally, but rest assured your name is in the running unless you opt out.
Im looking for $50.00 per plus $5 for domestic shipping and $15 international.
steel barrel, screws (one M6 and 2 M3) and the connecting post with the correct flat ends.
Hope this finds everyone well,
-Michael
Here is the Sign up list for the second run. Ive added in those of you that had wanted one last time. Ill be contacting you to make sure that is still the case.
Second run
1. repdetect.........................Confirmed..........Payment Received......Sent
2. Photech...........................Confirmed..........Payment Received
3. anonymous......................Not Confirmed
4. DBoz...............NoTang..... Confirmed..........Payment Received......Sent
5. ironfist.............................Confirmed..........Payment Received......Sent
6. kurtyboy..........................Confirmed
7. Bwood.............................Confirmed..........Payment Received......Sent
8. TKY2019..........................Not Confirmed
9. beal.................................Confirmed..........Payment Received......Sent
10. tain669...........................Not Confirmed
11. technocoy.......................Confirmed..........Payment Received
12. Vader.............................Confirmed..........Payment Received......Sent
13. Starr..............................Confirmed..........Payment Received......Sent
14. QuartZ............................Confirmed.........Payment Received......Sent
15. hirohawa.........................Confirmed.........Payment Received......Sent
16. Fedgunlover.....................Confirmed........Payment Received......Sent
17. blastmaster.............................................Payment Received......Sent
18. ironfist for a second one...Confirmed........Payment Received......Sent
19. cratercritter.....................Confirmed........Payment Received
20. cratercritter.....................Confirmed........Payment Received
21.
22.
23.
24.
25.
Last edited by mspaw on Tue Jun 28, 2011 7:22 pm; edited 24 times in total |
|
Back to top |
|
|
|
|
|
|
|
|
|
|
|
Author |
Message |
hirohawa Community Member
Joined: 18 May 2006 Posts: 1067
|
Posted: Fri May 06, 2011 9:49 pm Post subject: |
|
|
Welcome back. |
|
Back to top |
|
|
|
|
|
|
|
|
|
|
|
Author |
Message |
mspaw Community Member
Joined: 18 Mar 2007 Posts: 234 Location: Sacramento CA
|
Posted: Sat May 07, 2011 12:00 am Post subject: |
|
|
Thanks!
Nice to be back
-Michael |
|
Back to top |
|
|
|
|
|
|
|
|
|
|
|
Author |
Message |
DBoz Community Member
Joined: 07 Jul 2009 Posts: 19 Location: Sacto, CA
|
Posted: Sat May 07, 2011 5:09 am Post subject: |
|
|
Wow, what timing. I recently have had a renewed interest in my BR Blaster and was wondering what happened to this. I believe I am on the list, but would just like to re-confirm that I am still interested in one of these barrels. |
|
Back to top |
|
|
|
|
|
|
|
|
|
|
|
Author |
Message |
joberg Community Member
Joined: 06 Oct 2008 Posts: 9447
|
Posted: Sat May 07, 2011 6:59 am Post subject: |
|
|
Very good work...I'm always amazed at how many talented people are on this board: maybe a good idea for the Mods should be a list of key people specialized in a particular skill: i.e. Michael and Don: replacement barrels, grip, etc. Other members are skilled in paper props, others in badges...well you get my drift |
|
Back to top |
|
|
|
|
|
|
|
|
|
|
|
Author |
Message |
technocoy Community Member
Joined: 21 Jan 2008 Posts: 86 Location: NC
|
Posted: Sat May 07, 2011 7:42 am Post subject: |
|
|
Hey man, good to have you back.
Now, if I remember correct, these work with the Sidkit worldcon version right?
If so, throw me on the list. It'll make a great addition along with my sight rod!
Also, you REALLY should consider getting your hands on a tomenosuke blaster and making us al some barrels and such. There are several parts on that puppy that I'm thinking a LOT of people would love to have up to par with the rest of the gun.
The barrel and frame are a high density abs, which is plenty strong, but it's just not metal.
Thanks for all your work, bro. |
|
Back to top |
|
|
|
|
|
|
|
|
|
|
|
Author |
Message |
Vader Community Member
Joined: 19 Feb 2011 Posts: 267 Location: Sweden
|
Posted: Sat May 07, 2011 7:43 am Post subject: |
|
|
Nice looking barrels...! These are primarily designed to fit the Sidkit, is that correct?
Is the difference in tone (light upper row/dark lower row) a real feature, or merely an artifact of the lighting where the photo was taken? _________________ 26354 |
|
Back to top |
|
|
|
|
|
|
|
|
|
|
|
Author |
Message |
Staar Community Member
Joined: 04 Feb 2008 Posts: 757 Location: AUSTRALIA
|
Posted: Sat May 07, 2011 9:22 am Post subject: |
|
|
I'm in..
best
Mark _________________
|
|
Back to top |
|
|
|
|
|
|
|
|
|
|
|
Author |
Message |
mspaw Community Member
Joined: 18 Mar 2007 Posts: 234 Location: Sacramento CA
|
Posted: Sat May 07, 2011 7:57 pm Post subject: Machined barrels |
|
|
Thanks everyone for the nice notes. I'll set up the sign up sheet tonight when I get back into town. As for the color, yep, it's just lighting, sorry for the confusion. They are just machined cold rolled steel, suitable for bluing. And yes they are based off of the Sid kit, though I know some people have used them for rich's kit as well. Adam Savage used one for his real bulldog and Styre replica as well.
I'll be sending conformation pm's to those who have signed up tonight as well.
-Michael |
|
Back to top |
|
|
|
|
|
|
|
|
|
|
|
Author |
Message |
mspaw Community Member
Joined: 18 Mar 2007 Posts: 234 Location: Sacramento CA
|
Posted: Sun May 08, 2011 2:58 pm Post subject: |
|
|
The sign up list is in place and ill be contacting everyone that has put in a request so far.
Thanks!
-Michael |
|
Back to top |
|
|
|
|
|
|
|
|
|
|
|
Author |
Message |
Photech Community Member
Joined: 05 May 2009 Posts: 207 Location: Australia
|
Posted: Sun May 08, 2011 11:28 pm Post subject: |
|
|
Yes please I'm in. Are the holes tapped? Is the barrel drilled all the way through? Thx _________________ No! 4, 2 - 2, 4. |
|
Back to top |
|
|
|
|
|
|
|
|
|
|
|
Author |
Message |
mspaw Community Member
Joined: 18 Mar 2007 Posts: 234 Location: Sacramento CA
|
Posted: Mon May 09, 2011 12:15 am Post subject: |
|
|
Holes are tapped and blind and the barrel is drilled out and reamed to nearly the full depth.
-Michael |
|
Back to top |
|
|
|
|
|
|
|
|
|
|
|
Author |
Message |
Staar Community Member
Joined: 04 Feb 2008 Posts: 757 Location: AUSTRALIA
|
Posted: Mon May 09, 2011 1:32 am Post subject: |
|
|
Is the bore clockwise or anti-clockwise???
Cheers again mate.
Kind regards
MARK _________________
|
|
Back to top |
|
|
|
|
|
|
|
|
|
|
|
Author |
Message |
mspaw Community Member
Joined: 18 Mar 2007 Posts: 234 Location: Sacramento CA
|
Posted: Mon May 09, 2011 11:22 am Post subject: |
|
|
Mark-
For you, Ill make one anti-clockwise...
-Michael |
|
Back to top |
|
|
|
|
|
|
|
|
|
|
|
Author |
Message |
Photech Community Member
Joined: 05 May 2009 Posts: 207 Location: Australia
|
Posted: Mon May 09, 2011 4:51 pm Post subject: |
|
|
PP information plz _________________ No! 4, 2 - 2, 4. |
|
Back to top |
|
|
|
|
|
|
|
|
|
|
|
Author |
Message |
mspaw Community Member
Joined: 18 Mar 2007 Posts: 234 Location: Sacramento CA
|
Posted: Mon May 09, 2011 5:46 pm Post subject: |
|
|
Done and done.
-Michael |
|
Back to top |
|
|
|
|
|
|
|
|
|
|
|
Author |
Message |
Staar Community Member
Joined: 04 Feb 2008 Posts: 757 Location: AUSTRALIA
|
Posted: Mon May 09, 2011 7:56 pm Post subject: |
|
|
mspaw wrote: | Mark-
For you, Ill make one anti-clockwise...
-Michael |
_________________
|
|
Back to top |
|
|
|
|
|
|
|
|
|
|
|
Author |
Message |
jakob2121 Community Member
Joined: 06 Dec 2008 Posts: 98
|
Posted: Mon May 09, 2011 9:29 pm Post subject: |
|
|
Speaking of the Tomenosuke, I thought someone had elsewhere said that they'd used one of his other barrels on the new v2 and it worked, though he had to drill new holes for the steyr screws. Anyway, if you manage to do a run of Tv2 barrels, I'm in for one. |
|
Back to top |
|
|
|
|
|
|
|
|
|
|
|
Author |
Message |
Fedgunlover Community Member
Joined: 15 Feb 2011 Posts: 28
|
Posted: Tue May 10, 2011 7:07 am Post subject: |
|
|
I will take one for use on Rich's plastic kit, when he finishes them. |
|
Back to top |
|
|
|
|
|
|
|
|
|
|
|
Author |
Message |
blastmaster Community Member
Joined: 06 Apr 2011 Posts: 37 Location: VALENCIA CA.
|
Posted: Tue May 10, 2011 10:51 am Post subject: Steel Barrel |
|
|
Hi Michael,
I will take one as well. What is Paypal info and will send over a payment.
Thanks,
AL |
|
Back to top |
|
|
|
|
|
|
|
|
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
|
|
|
|
|
|
|