FAQ Search Memberlist Usergroups Profile Log in to check your private messages
 Forum Index      Log in  Register
New Front Trigger info for Real K Frame Triggers!

 
Post new topic   Reply to topic     Forum Index -> Blade Runner Blaster Information and Discussion
View previous topic :: View next topic  
Author Message
ogrotesque1
Community Member


Joined: 30 Sep 2016
Posts: 130
Location: La Palma, CA

PostPosted: Tue May 22, 2018 3:59 pm    Post subject: New Front Trigger info for Real K Frame Triggers! Reply with quote

OK so, I apparently found out something that was driving me crazy for some time now and it was all by accident! I haven’t seen much info on the Front K Frame Trigger details other than the trigger must be machined in such a way to fit correctly, not anymore! Well, sort of...
This machining would have to be done if your Trigger was at or above a thickness of .138” and up. K, N & L Frame Triggers can get as thick as .400” in some cases!
My point being, if you find a trigger that is at a thickness of .138” to .240” you’re good, no milling down the side so it doesn’t interfere with the Bulldogs functionality! You will still need to make a notch on the forward top Left side looking from the serrations. That can easily be done with a dremel if your Trigger is not case hardened.
So, make sure you pay attention that the trigger you purchase has a thickness of only .138” kiddos! It’ll save you from a ton of work on such a small detail.

http:///upload/2816/1bbe2547-322d-4744-80e4-f0c4982f5251.jpeg
http:///upload/2816/1c361663-c38c-4c99-90c9-48f6c59ded53.jpeg
http:///upload/2816/1427686d-14d1-4055-bef8-f9df767a1fc5.jpeg

Hope this helps all you real shooters,
Damion
_________________

Damion: ogrotesque1


Last edited by ogrotesque1 on Fri Jun 15, 2018 1:21 pm; edited 2 times in total
Back to top
View user's profile Send private message Yahoo Messenger
Author Message
ogrotesque1
Community Member


Joined: 30 Sep 2016
Posts: 130
Location: La Palma, CA

PostPosted: Wed May 23, 2018 12:45 am    Post subject: Reply with quote

I hope these photos are working for you guys!? Sorry if they aren’t, I tried...
_________________

Damion: ogrotesque1
Back to top
View user's profile Send private message Yahoo Messenger
Author Message
Staar
Community Member


Joined: 04 Feb 2008
Posts: 736
Location: AUSTRALIA

PostPosted: Wed May 23, 2018 1:54 am    Post subject: Reply with quote

Can't see them my end..
_________________

Back to top
View user's profile Send private message Visit poster's website
Author Message
ogrotesque1
Community Member


Joined: 30 Sep 2016
Posts: 130
Location: La Palma, CA

PostPosted: Wed May 23, 2018 7:52 am    Post subject: Reply with quote

Staar wrote:
Can't see them my end..


Thanks, I’ll try again.....
_________________

Damion: ogrotesque1
Back to top
View user's profile Send private message Yahoo Messenger
Author Message
Silverside
Community Member


Joined: 22 Jul 2017
Posts: 51
Location: UK

PostPosted: Wed May 23, 2018 8:59 am    Post subject: Reply with quote

Do you know which models this width trigger comes from?
I have access to Smith & Wesson triggers from model 28, model 36 and model 60 revolvers but I don't want to buy the wrong one and do loads of extra work on it now you have given such useful information.
Back to top
View user's profile Send private message
Author Message
ogrotesque1
Community Member


Joined: 30 Sep 2016
Posts: 130
Location: La Palma, CA

PostPosted: Wed May 23, 2018 1:39 pm    Post subject: Reply with quote

I’m not all that certain as to which model = which trigger other than, K, N & L Frame Triggers vary from one another due to each Frames functionality.
Most of us on here believe that a K Frame Trigger is the “Screen Accurate” Trigger used for the Hero.
Just use calipers to check the width of your trigger you have access too before hand. Most sellers will usually specify which Frame the trigger is made for and it’s width in inches.
Good luck,
Damion

Silverside wrote:
Do you know which models this width trigger comes from?
I have access to Smith & Wesson triggers from model 28, model 36 and model 60 revolvers but I don't want to buy the wrong one and do loads of extra work on it now you have given such useful information.

_________________

Damion: ogrotesque1
Back to top
View user's profile Send private message Yahoo Messenger
Display posts from previous:   
Post new topic   Reply to topic     Forum Index -> Blade Runner Blaster Information and Discussion All times are GMT - 5 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

Powered by phpBB © 2001, 2002 phpBB Group
BBTech Template by © 2003-04 MDesign

Problems Registering Contact: help@propsummit.com